Backpack Laser Cleaning Machine MW-LC50: Clean at Height and in Tight Spaces

Operator wearing the MAXWAVE MW-LC50 backpack laser cleaning machine, handheld cleaning head in his right hand

The MAXWAVE MW-LC50 series is a pulsed laser cleaning machine that the operator wears on their back, for maintenance teams, equipment repair companies and field service crews whose dirty surfaces sit up a ladder, on a platform, inside an enclosure or between other equipment.

The operator carries it to the part, climbs with it and cleans with the handheld head in reach of the surface, where a cabinet cannot stand and a case cannot be wheeled. Built for thin layers: light rust, thin oxide, paint spots and residue films.

  • 50 to 200 WPulsed fiber laser
  • 12 kgComplete machine, worn on the back
  • 6Cleaning modes
  • AirCooled, no chiller

Jobs the MW-LC50 Is Built For

The backpack laser cleaner earns its place where the difficult part is reaching the surface, not covering a large area fast.

Built for

  • Gear teeth meshing on an installed drive, a typical backpack laser cleaning job

    Gears and drive parts in place

    Light rust, grease residue and oxide off gears, shafts and couplings on installed machinery, so the drive is not stripped out and carried to a workshop.Case record: 100 W backpack unit on metal gears, about 3 to 4 m²/h
  • Laser taking a local patch of rust off a steel box down to bare metal

    Spots of rust and paint at height

    Local corrosion and flaking paint on brackets, frames and beams reached from a ladder, a scaffold or an access platform, ahead of repair or repainting.
  • Laser cleaning the inside of a recessed steel cavity

    Inside enclosures and tight spaces

    Surfaces inside machine housings, equipment bays, pits and vessels, where there is no floor space for a cabinet or a case.
  • Stainless part with heat tint oxide, half cleaned back to bright metal

    Thin oxide and light rust before repair

    A small area of steel prepared for welding, inspection or coating, one patch at a time.
  • Rusty ribbed steel bars outdoors with a cleaned strip down the middle

    Field maintenance away from the workshop

    Jobs on customer premises or outdoor installations, where the crew walks or climbs the last stretch to the equipment.

Also typical: oxide and paint on pipe joints, flanges and supports before inspection, and a cleared patch on a housing, guard or mounting face when a part is repaired in place. How maintenance teams fit this into shutdown work: laser cleaning for industrial maintenance.

MW-LC50 reference cleaning rates by layer
LayerMW-LC50 reference
Paint, coatings and other organic layersapprox. 4 to 8 m²/h at 50 to 200 W
Oxide and rustThin oxide and light rust; not heavy scale

Rates are approximate and vary with the base material, the layer and the settings.

Jobs to give a different machine

We tell buyers plainly where the MW-LC50 is the wrong choice. Three kinds of work belong on another line.

  • MAXWAVE MW-LCW water-cooled CW laser cleaning cabinet

    Heavy rust and scale over large steel areas

    A 50 to 200 W pulsed unit takes a thin layer at a time. The MW-LCW removes rust and oxide at about 5 to 10 m²/h at 2000 to 6000 W, in a workshop cabinet the parts come to.Water-cooled CW laser cleaning machine
  • MAXWAVE MW-LCW laser cleaning cabinet for large coated surfaces

    Stripping paint from whole large surfaces

    For square meters of coating, the MW-LCW runs at about 10 to 20 m²/h on organic layers at 1500 to 6000 W. On steel sheet thinner than 4 mm, continuous paint removal can distort the sheet, so thin sheet goes to our pulsed cabinet line.MW-LCW for coatings
  • MAXWAVE MW-LY air-cooled pulse laser cleaning cabinet

    Full-shift cleaning at a fixed station

    The MW-LC50 is made for mobile work in sessions. A station that cleans parts all shift long is better served by the MW-LY cabinet at 100 to 500 W, or the MW-LCW, whose chiller is built for long running hours.Air-cooled pulse laser cleaner

Mixed work? Daily production cleaning plus occasional repairs at height: say so in your requirement. The engineer may recommend a cabinet unit for the line and a backpack unit for the maintenance crew.

Worn by One Operator: 12 kg Complete Machine

33 × 16.8 × 38 cm and 12 kg with the laser source, cooling and controls inside: less than half our 25 kg trolley case, and the only unit in our range that travels on a person.

Operator standing with the MW-LC50 on his back, cleaning head in one hand and control screen in the other
One operator, whole job
Side view of the MW-LC50 sitting close to the operator's back on two shoulder straps
Unit on the back, hands at the front
Operator holding the MW-LC50 handheld cleaning head, fiber hose running from the backpack
Head and hose go where he goes
MW-LC50 backpack unit from the side, showing its slim depth and harness
33 cm wide, 16.8 cm deep
One person

One operator does the whole job

The operator carries the unit, gets into position and works the handheld cleaning head, with no machine to move along on the ground. Confined-space entry still follows your site's own permit and attendant rules.

Hands free

Hands free while moving

With the unit on the back, the operator's hands stay free for ladder rungs, handrails and hatch edges on the way to the work point.

No case to move

The machine moves with the operator

Along a platform, around a vessel or from one gearbox to the next, the unit goes where the operator goes: no case to reposition and no distance to walk back for.

33 × 16.8 cm

Room in narrow spaces

At 33 cm wide and 16.8 cm deep, the unit stays close to the operator's body in openings and in the gaps between equipment.

Packed: 43 × 27 × 48 cm, 22 kg
Ships as a single compact carton. Between jobs it stores on a shelf in the service van or the maintenance store.

Preparing a Job at Height or in a Confined Space

Laser cleaning above ground or inside a closed space adds risks of its own. The crew confirms five points before the operator goes up or goes in.

Hand gripping the MW-LC50 handheld laser cleaning head
Both hands are in use while cleaning

Operator protective equipment, laser safety setup and fume extraction are covered on our support and maintenance page.

Five points before going up or going in

Confirmed by the crew for every job at height or in an enclosure.
  • Footing and fall protection

    A stable platform or a secured ladder, with fall protection set up under the site's own work-at-height rules, because both hands are in use while cleaning.
  • A controlled laser area

    The MW-LC50 is a Class 4 laser. Keep people out of the zone or protected. On a platform the zone includes people working below; in a vessel it is the whole space.
  • Reflective surfaces

    Polished steel, stainless walls and bright metal can bounce the beam back at the operator or a coworker. Screen them, or angle the head so reflections point away from people.
  • Fume extraction

    The removed layer becomes fume and fine particles, and in an enclosure they collect fast. Run extraction at the cleaning point and ventilate the space for the whole job.
  • Lighting

    Inside housings, pits and vessels, set work lights on the surface so the operator sees when the layer is gone and stops there.

Backpack vs Trolley Case at a Glance

Both portable lines are pulsed and air cooled. The difference is how the machine reaches the part.

MW-LC50 backpack compared with the MW-LC trolley case
ItemMW-LC50 backpackMW-LC trolley case
CarriedOn the operator's backPulled on wheels
Machine weight12 kg25 kg
Laser power50 to 200 W pulsed100 to 300 W pulsed
Cleaning widthapprox. 100 to 130 mmapprox. 100 to 160 mm
Cleaning modes66
Best placed forLadders, platforms, confined spacesPlant floors, repair bays, customer sites at ground level
MAXWAVE MW-LC trolley-case laser cleaner

Ground level, up to 300 W

If your crews mostly work at ground level and want more power, see the trolley-case laser cleaner.

Pulsed, Air-Cooled Source

Ready soon after it is set up at the work point, for crews who clean in short stints between other repair tasks.

Pulsed fiber laser

Pulsed cleaning puts little heat into the base material, which suits thin parts, finished surfaces and precision parts such as gears.

Air cooled, no chiller

No chiller and no water to carry, so the unit moves between several points on a site and starts cleaning at each.
MW-LC50 laser cleaning control screen with power and mode settings
MW-LC50 control screen

Rate Estimate for Your Layer

Send photos of your parts and the engineer gives a rate estimate for your layer and power class.

Send Photos on WhatsApp
MAXWAVE MW-LC50 backpack laser cleaning machine on a bench with its control screen and cleaning head
MW-LC50 with control screen and handheld head

MW-LC50 Technical Specifications

Laser power
50 to 200 W
Laser type
Pulsed fiber
Cooling
Air
Cleaning modes
6
Cleaning width
approx. 100 to 130 mm, by model
Carrying
Worn on the operator's back
Machine size
33 × 16.8 × 38 cm
Machine weight
12 kg
Packed size
43 × 27 × 48 cm
Packed weight
22 kg

Series MW-LC50 to 200. The engineer confirms the power class within the series from the layer and the parts you describe.

Get a Quote for the MW-LC50 Backpack Laser Cleaning Machine

An engineer replies with the MW-LC50 power class for your work, or names another of our machines if your job calls for one.

Six details for the right power class

  • Material: the base metal of the parts.
  • Layer: the rust, oxide, paint or residue to remove.
  • Where the parts sit: height, enclosure or field site.
  • Surface: how much a typical job covers.
  • Country: where your crews work.
  • Photo: one of the part. Photos can follow on WhatsApp.

Phone / WhatsApp: +86 15327155363 · Call